符合標準：

GB1410《固體電工絕緣材料絕緣電阻、體積電阻系數和表面電阻試驗方法》 
ASTM D257《絕緣材料的直流電阻或電導試驗方法》 

一、概述 

    既可測量高電阻，又可測微電流。采用了美國In公司的大規模集成電路,使儀器體積小、重量輕、準確度高。以雙3.1/2 位數字直接顯示電阻的高阻計和電流。量限從1×104Ω ～1×1018 Ω，是目前國內測量范圍zui寬，準確度zui高的數字超高阻測量?jī)x。電流測量范圍為2×10-4 ～1×10-16Ａ。機內測試電壓為10/50/100/250/500/1000V任意可調。本儀器具有精度高、顯示迅速、性好穩定、讀數方便， 適用于防靜電產品如防靜電鞋、防靜電塑料橡膠制品、計算機房防靜電活動地板等電阻值的檢驗以及絕緣材料和電子電器產品的絕緣電阻測量。固體絕緣材料體積/表面電阻率測定儀除能測電阻外，還能直接測量微弱電流。

三、技術指標 

四、工作原理 

    根據歐姆定律，被測電阻Rx等于施加電壓V除以通過的電流I。傳統的高阻計的工作原理是測量電壓V固定，通過測量流過取樣電阻的電流I來得到電阻值。從歐姆定律可以看出，由于電流I是與電阻成反比，而不是成正比，所以電阻的顯示值是非線性的，即電阻無窮大時，電流為零，即表頭的零位處是∞，其附近的刻度非常密，分辨率很低。整個刻度是非線性的。又由于測量不同的電阻時，其電壓V也會有些變化，所以普通的高阻計是精度差、分辨率低。 
    本儀器是同時測出電阻兩端的電壓V和流過電阻的電流I，通過內部的大規模集成電路完成電壓除以電流的計算，然后把所得到的結果經過A/D轉換后以數字顯示出電阻值，即便是電阻兩端的電壓V和流過電阻的電流I是同時變化，其顯示的電阻值不象普通高阻計那樣因被測電壓V的變化或電流Ｉ的變化而變，所以，即使測量電壓、被測量電阻、電源電壓等發生變化對其結果影響不大，其測量精度很高()，從理論上講其誤差可以做到零，而實際誤差可以做到千分之幾或萬分之幾。 

典型應用 

1．測量防靜電鞋、導電鞋的電阻值 
2、測量防靜電材料的電阻及電阻率 
3、測量計算機房用活動地板的系統電阻值 
4、測量絕緣材料電阻(率) 
5、光電二極管暗電流測量 
6、物理,光學和材料研究 

標準配置： 

Meet the standard:

GB1410《固體電工絕緣材料絕緣電阻、體積電阻系數和表面電阻試驗方法》

GB1410 "solid electrical insulation materials insulation resistance, volume resistivity and surface resistivity test method"

ASTM D257《絕緣材料的直流電阻或電導試驗方法》

DC resistance or conductance of insulating materials test method "ASTM D257"

一、概述

One, overview

既可測量高電阻，又可測微電流。采用了美國In公司的大規模集成電路,使儀器體積小、重量輕、準確度高。以雙3.1/2 位數字直接顯示電阻的高阻計和電流。量限從1×104Ω ～1×1018 Ω，是目前國內測量范圍zui寬，準確度zui高的數字超高阻測量?jī)x。電流測量范圍為2×10-4 ～1×10-16Ａ。機內測試電壓為10/50/100/250/500/1000V任意可調。本儀器具有精度高、顯示迅速、性好穩定、讀數方便， 適用于防靜電產品如防靜電鞋、防靜電塑料橡膠制品、計算機房防靜電活動地板等電阻值的檢驗以及絕緣材料和電子電器產品的絕緣電阻測量。固體絕緣材料體積/表面電阻率測定儀除能測電阻外，還能直接測量微弱電流。

Not only can measure high resistance, but also can measure current. Use of large scale integrated circuit America In company, make the instrument has the advantages of small volume, light weight, high accuracy. High resistance meter and current resistors directly to double 3.1/2 digital display. Range from 1 × 104 Ω to 1 × 1018 Ω, is currently the most wide measuring range, accuracy the highest high resistance measuring instrument. Current measuring range is 2 × 10-4 ～ 1 × 10-16A. The built-in test voltage of 10/50/100/250/500/1000V adjustable. The instrument has high precision, good stability, shows a rapid, convenient reading, suitable for measuring insulation resistance in anti-static products such as anti-static shoes, anti-static plastic and rubber products, computer room anti electrostatic floor activities such as inspection resistance and insulation materials and electronic products. The volume / surface resistivity tester can measure resistance in solid insulation, and can directly measure weak current.

三、技術指標

Three, technical indicators

序號 項目 參數

The number of item parameters

1 電阻測量范圍 1×104Ω ～1×1018Ω

1 resistance measurement range of 1 × 104 to 1 × 1018 Ω

2 電流測量范圍 2×10-4A～1×10-16A

2 current measurement range of 2 × 10-4A ～ 1 × 10-16A

3 雙表頭顯示 3.1/2位LED顯示

3 double headers 3.1/2 LED display

4 內置測試電壓 10V、50V、100V、250、500、1000V

4 built-in test voltage of 10V, 50V, 100V, 250, 500, 1000V

5 基本準確度 1%

5 basic accuracy 1%

6 使用環境 溫度：0℃～40℃，相對濕度<80%

6 the use of environmental temperature: 0 ℃ ~ 40 ℃, relative humidity <80%

7 機內測試電壓 10/50/100/250/500/1000V 任意切換

7 built-in test voltage 10/50/100/250/500/1000V switch

8 供電形式 AC 220V，50HZ，功耗約5W

The 8 power supply form of AC 220V, 50HZ, power consumption is about 5W

9 儀器尺寸 285ｍｍ× 245ｍｍ× 120 mm

The 9 instrument size 285mm × 245mm × 120 mm

10 質量 約2.5KG

10 quality about 2.5KG

四、工作原理

Four, work principle

根據歐姆定律，被測電阻Rx等于施加電壓V除以通過的電流I。傳統的高阻計的工作原理是測量電壓V固定，通過測量流過取樣電阻的電流I來得到電阻值。從歐姆定律可以看出，由于電流I是與電阻成反比，而不是成正比，所以電阻的顯示值是非線性的，即電阻無窮大時，電流為零，即表頭的零位處是∞，其附近的刻度非常密，分辨率很低。整個刻度是非線性的。又由于測量不同的電阻時，其電壓V也會有些變化，所以普通的高阻計是精度差、分辨率低。

According to Ohm's law, the measured resistance Rx is equal to the applied voltage divided by current V by I. The working principle of high resistance meter is the traditional measure voltage V fixed, by measuring the current flows through the sampling resistor I to get the resistance value. From Ohm's law can be seen, the current I is inversely proportional to the resistance, not proportional, so is nonlinear resistive display value, namely the infinite resistance, current is zero, i.e. zero at the header is ∞, graduated in the vicinity of the very tight, very low resolution. The scale is nonlinear. Because the resistance measurement is different, its voltage V there will be some changes, so the high resistance of ordinary meter is poor accuracy, low resolution.

本儀器是同時測出電阻兩端的電壓V和流過電阻的電流I，通過內部的大規模集成電路完成電壓除以電流的計算，然后把所得到的結果經過A/D轉換后以數字顯示出電阻值，即便是電阻兩端的電壓V和流過電阻的電流I是同時變化，其顯示的電阻值不象普通高阻計那樣因被測電壓V的變化或電流Ｉ的變化而變，所以，即使測量電壓、被測量電阻、電源電壓等發生變化對其結果影響不大，其測量精度很高()，從理論上講其誤差可以做到零，而實際誤差可以做到千分之幾或萬分之幾。

This instrument is current and voltage V and flow resistance at the same time measuring resistor I, the large scale integrated circuit internal to complete the calculation of voltage divided by current, and then the obtained results after A/D conversion to digital display resistance value, even if is current and voltage of V and flow resistance at both ends of the I is changed at the same time, the displayed value resistance do not like ordinary high resistance meter that due to changes in the measured voltage or current change of V I and change, so, even if the measurement of voltage, resistance, power supply voltage is measured and the change had little effect on the results, the measuring accuracy is very high (patent), theoretically the error can do zero, while the actual error can be done a few thousandths or very few.

典型應用

Typical applications

1．測量防靜電鞋、導電鞋的電阻值

Resistance of 1 measurements of anti-static shoes, conductive shoes value

2、測量防靜電材料的電阻及電阻率

2, the measurement of anti resistance and resistivity electrostatic materials

3、測量計算機房用活動地板的系統電阻值

3, the measurement used in computer room floor system resistance value

4、測量絕緣材料電阻(率)

Insulation resistance 4, measurement (rate)

5、光電二極管暗電流測量

5, photoelectric diode dark current measurement

6、物理,光學和材料研究

6, physical, optical and material research

標準配置：

Standard configuration:

序號 配置 數量 單位

Number allocation unit

1 測試儀器 臺 1

1 test instrument platform 1

2 電源線 條 1

2 power line 1

3 測量線 根 3

3 measuring line 3

4 使用說明書 份 1

4 Manual 1